Metric system

Is an international system which is a decimal based system, consequently, conversions from one unit to another within the metric system can accomplished by multiplying or dividing by ten or power of ten.

Note: With the exception of temperature, amount of substance and luminous intensity international other units of measurement that are smaller or larger than the most commonly used units are expressed by attaching a prefix to the most commonly used units.



More than 1 unit
 Giga(G) = 1,000,000,000 (10ˆ9)
 Mega(M) = 1,000,000 (10ˆ6)
 Kilo(K) = 1,000(10ˆ3)
 Hector (h) = 100(10ˆ2)
 Decca(da) = 10(10ˆ1)1 Less than 1 unit
Deci (d) = 1/10 (10ˆ-1)
Cent (c) = 1/100(10ˆ-2)
Mill (m) = 1/1000 (10ˆ-3)
Micro(μ) = 1/1,000,000(10ˆ-6)

Appropriate Instruments for Measuring Fundamental Quantities

Length, l
Length is the distance between two points, objects or space.The SI unit of length is meter(m). The instrument used to measure length is the metre rule.
Other commonly used units are kilometer(km) and centimeter(cm).

1km = 1000m
1m = 100cm


How to read the metre rule:
Owing to the thickness of the wood,the eye must always be placed vertically above the mark being read, in order to avoid errors due to parallax.


Measuring of length (diameter) of small objects.
The diameter of small objects is measured by using two instruments:
a. Vernier caliper
b. Micrometer screw gauge

A vernier caliper:

Is the instrument used to measure length to the accuracy of 0.01cm.

It is used to measure lengths to the range of 1.0cm to about 12.0cm.

The figure below describe the structure of vernier caliper.




The main scale is graduated in centimeter (cm) while the vernier scale is graduated in millimeter (mm).The vernier scale is a short scale 9mm long divided into 10 equal parts, so that the difference in length between a vernier division and the main scale division is 0.1mm or 0.01cm.
The inside jaws are used to measure the inside diameter while the outside jaws are used to measure outside diameter.The vernier slides over the main scale.

How to read
 The main scale reading is recorded. This is the reading which precedes the zero mark of the vernier scale.
 The vernier scale reading is recorded by reading the mark on it which coincide with a mark on the main scale (i.e. vernier scale reading x 0.01cm).
 The summation of these two readings is the length of the object measured.

A micrometer screw gauge:

Is an instrument used to measure length to the accuracy of 0.001cm(0.01mm).

It is used to measure the diameters of wires and ball bearings. It can measure small lengths up to about 2.5cm.

The diagram below describes the micrometer screw gauge.




It consists of a spindle which is fitted with a graduated thimble. The screwed portion of a spindle is totally enclosed to protect it from damage. The pitch of the screw is 0.5mm, so that the spindle moves through o.o5cm for each complete turn.

The anvil and the spindle grip the measured object between them. The ratchet prevents the user from using undue pressure. The sleeve is graduated in mm, each graduation represent one complete turn of the screw.

How to read a micrometer screw gauge:
 Sleeve reading is recorded. This gives the units and the first two decimal places in mm.
 Thimble reading is then recorded. This gives the third decimal place (thimble reading x
0.001mm).
 The summation of these two readings gives the diameter of the object under measurement.


Precautions when using a micrometer screw gauge.
1. Before use,the faces of anvil and spindle should be wiped clean to remove any dirty particle which would give false readings.
2. Check and record for zero error then + or –the correction to the final answer.